Sorry, you need to enable JavaScript to visit this website.
  • Essai
  • Plan d'accès

How to classify my ATEX zone?

Partager la page
Filling
| 3 minutes of reading | By Loïc Simon
How to know my atex zone ?

Palamatic Process supports you in the design of your installations dealing with explosive powders. In this document, you will find an ATEX guide for equipment that complies with industrial process regulations.

 

1. Main causes of explosion

1. Presence of oxidant

Mainly oxygen in the air (O2 is "oxygen" for chemists) but also other gases such as Di-chlorine (Cl2), Nitrogen Dioxide (NO2), Nitrogen Trifluoro-mide (NF3)...


2. Presence of fuel

A flammable substance that can be: a gas (methane, acetylene, etc.), a liquid (gasoline, solvent, etc.) or a solid (sulfur, wood, sugar, flour, etc.), generally speaking, all organic powders.
NB: mineral type powders do not present any risk. 


3. Special form of fuel

- Gas (methane, acetylene, butane, propane, hydrogen, etc.)
- Steam (gasoline, ethyl alcohol, solvent, acetone, etc.)
- Dust (wood, sugar, grains, starch, aluminum, etc.)


4. Explosive range

To be explosive, the mixture must be neither too poor nor too rich in fuel.

  • LEL: the Lower Explosive or Flammable Limit (LEL or LII) of a gas or vapor in air, is the minimum volume concentration in the mixture above which it can be ignited. - source: ED911 from INRS
  • UEL: the Upper Explosive or Flammable Limit (UEL or UFL) of a gas or vapor in air is the maximum concentration by volume in the mixture below which it can be ignited. - source: ED911 from INRS

To be explosive, the mixture with air must meet the following condition: LEL< concentration of the flammable substance in the mixture < UEL.
Accuracy concerning dusts: "The minimum and maximum explosive concentrations of dusts are not known as precisely as those of gases".


5. Sufficient containment

In the absence of a containment enclosure, in a dust cloud that has just been ignited, the atmosphere consists of 2 parts:
- The rear front contains partially burnt gas and solid residues.
- In front unburnt dust is present.

This process creates a fireball. This "mixture" must be in a containment enclosure. In fact, we see the appearance of an pressure due to the combustible gas driving out the air which can lift the dust. The flame will then ignite the dust in the air which can occur as long as dust is present.


6. Source of ignition

- Electric (sparks, heating, etc.)
- Electrostatic discharges
- Temperature rise (e.g., hot surfaces)
- Thermal (open flames, cigarettes, hot surfaces, etc.)
- Mechanical (sparks, heating, etc.)
- Chemical (exothermic reaction, self-heating, etc.)
- Bacteriological (bacterial fermentation that can heat the medium and create self-heating conditions)
- Climate (lightning, sun, etc.).

Auto-ignition temperatures obtained with the IEC 1241-25-1 method:

Dust
(granulometry)
(Media value, μm)
Temp. ignition point of cloud at
the Godbert oven - Greenwald (°C)
Temp. ignition deposit of dust
layer 5 mm (°C)
Starch (52)
Cereals (50)
Charcoal (28)
Copra (510)
Wood flour (65)
Milk powder (60)
Corn (550)
Corn (28)
Soybean flour (20)
Sugar (30)
Tobacco (65) 
350
520
600
470
490
610
780
440
620
490
450
345
300
250
290
340
340
410
280
280
480
300

Identify the potential sources of ignition:

Ignition source

 

Location Type de zone Notes
Internal volume of the pipes of the conveying network Zone 20 This classification corresponds to the case where the flow of dusty air constitutes an explosive atmosphere
Internal filter volume, dusty air side Zone 20  
Internal filter volume, clean air side Zone 22 Depending on the effectiveness of the cleaning of the premises, remove the deposits
Volume of the room in which the filter is installed Zonne 22 or
unclassified
 

 

2. Devices for surface industries (Group II)

Zone 0 20 1 21 2 22
Nature of the atmosphere

G

Gas

D

Dust

G

Gas

Dust

G

Gas

D

Dust

Explosive atmosphere Permanent presence Intermittent presence Episodic presence
Category of appliances that can be used according to 94/9/CE 1 2 3

 

Atex zones

3. Gas groups

Group Gas reference IEMS (mm) EMI (mj)
I Méthane 1.14 0.28
IIA Propane 0.92 0.25
IIB Ethylene 0.65 0.07
IIC Hydrogen/Acetylene 0.37 1.011/0.017

 

IEMS: Maximum Experimental Interstice of Security
EMI: Minimum Inflammation Energy
IIB1 : IEMS > 0.85
IIB2 : IEMS > 0.75
IIB3 : IEMS > 0.65

Loic powder expert Palamatic

If your require further assistance,
I am at your entire disposal.

 

Loïc, powder expert

+1 438 238 5273

4. Dust groups

Groups Type dof dust Cut Resistance
IIIA Combustible particles in suspension > 500 μm -
IIIB Non conductive dust ≤ 500 μm > 10³ Ω.m
IIIC Conductive dust ≤ 500 μm ≤ 10³ Ω.m

5. Temperature classes (maximum temperatures)

Gas T1 (450) T2 (300) T3 (200) T4 (135) T5 (100) T6 (85)
Powder 450 300 200 135 100 85

6. Indices de protection (IP)

Protection against solid bodies
0   No protection
1
Protected against solid objects ≥50 mm (e.g. involuntary hand contact)
2
Protected against solid bodies ≥12 mm (e.g., fingers)
3
Protected against solid bodies ≥2.5mm (e.g., screw tools, etc.)
4
Protected against solid objects ≥1 mm (e.g., fine tools, small wires)
5
Protected against dust (no harmful deposits)
6
Totally protected against dust

 

Protection against liquid bodies
0   No protection
1
Protected against vertically falling drops of water
2
Protected against falling water inclined at 15 °
3
Protected against rainwater up to 60 ° from vertical
4
Protected against splashing water from all directions
5
Protected against jets of water from all directions
6
Protected against water jets and heavy seas from all directions
7
Protected against the effects of immersion
9
Protected against the effects of prolonged immersion under specified conditions

 

7. The explosive characteristics of powders

To consult the characteristics of explosive powders, consult our article.

PMAX: maximum explosion pressure, maximum pressure (generally measured in relation to atmospheric pressure) reached in a closed tank during the explosion of the most reactive oxidizer / fuel mixture.

KST: dust explosion coefficient, maximum rate of rising pressure, multiplied by the cubic root of the volume of the container, during explosion tests of the most reactive oxidizer / fuel mixture.

EMI: explosive atmosphere, mixture of flammable gases, vapors, or dust in air.

LEL: lower explosive limit, minimum concentration of gas or dust in the air below which there can be no explosion.

GRANULOMETRY: average diameter of dust particles, usually measured using a laser particle size analyzer, or determined by sieving. The risk of explosion is considered when the particle diameter is less than 300 microns.

TMI Cloud / Dust: The auto-ignition temperature or auto-ignition temperature is the lowest temperature at which the substance ignites when mixed with air under the conditions defined in the test method without any other input of energy as flame or spark. Unit: ° K

Palamatic Process can assist you in analysing your risks and proposing equipment that is suitable for your powders and processes under ATEX atmosphere. Our experts are certified in accordance with the current regulations. Contact us for more information!

Stay informed of new articles by e-mail.

*By entering your email address, you agree to receive our latest articles and have read our privacy policy. You can unsubscribe at any time by contacting us at contact@palamatic.fr.

Discover the Palamatic Process know-how

Come and test our equipment in our test plant